LAN Cable Extension Kit for Camera Module on Raspberry Pi/NVIDIA Jetson

SKU
U6279
$49.99
-
+
Overview
  • Plug-and-play cable extension kit
  • Up to 10-meter cable extension
  • No additional software configure needed
  • Compatible with official Raspberry Pi camera and many Arducam cameras

Overview

This LAN extension cable kit is a solution for connecting the camera module to the processor over long distances. Replacing the CSI cable (Camera Serial Interface) with a LAN/Ethernet cable extend the length of the available cable and places the camera module up to 10 meters away from the Raspberry Pi/NVIDIA Jetson board. No additional drivers or software are required to control your camera module from a distance.
The extension kit consists of two parts: the transmitter board (Tx board), which is used to connect the camera module, and the receiver board (Rx board), which is securely fastened to the processor via GPIO pins. Below is the list of camera modules supported by the kit:

Supported Camera Modules Video Modes
Product Series for Raspberry Pi for NVIDIA Jetson*
Camera Module V1 (OV5647) 1080p 30 fps, 720p 60fps, 480p60fps/90fps /
Camera Module V2 (IMX219) 1080p47, 1640 × 1232p41 and 640 × 480p206 3280x2464@21fps
3280x1848@28fps
1920x1080@30fps
1640x1232@30fps
1280x720@60fps
HQ Camera (IMX477) 2028 × 1080p50, 2028 × 1520p40 and 1332 × 990p120 4056x3040@10fps
2028x1520@30fps
2028x1080@30fps
Camera Module V3 (IMX708) 2304 × 1296p56, 2304 × 1296p30 HDR, 1536 × 864p120 /
Arducam IMX519 Camera 1080p30, 720p60 4656x3496@9fps
3840x2160@17fps
1920x1080@60fps
1280x720@120fps
Arducam 64MP Camera 1280x720 @120fps
1920x1080@60fps
2312x1736@30fps
3840x2160@20fps
4624x3472@10fps
8000x6000@3fps
[email protected]
/
Arducam ToF Camera (B0410) 240x180@30fps 240x180@30fps
* Tested on Jetson Orin NX/Orin Nano/Xavier NX/Nano (L4t 35.3.1 Jetpack5.1.1/L4t 32.7.3 Jetpack4.6.3)
When used on the NVIDIA Jetson Nnao/Xavier NX, a longer 15-15 pin FPC is needed. When used on the Orin Nano/Orin NX, a longer 15-22 pin FPC is needed.

 


Applications

  • UAV/Drones/FPV camera
  • Machine Vision
  • Robotics
  • Face Recognition
  • Defect Detection

Operation Steps

Operation Steps Assembly Instructions
1 Plug the Rx board into the Raspberry Pi board;
2 Plug the Tx board into the Raspberry Pi camera;
3 Connect the Rx and Tx boards with a network cable.

Package Including

  • 1 x The Rx board
  • 1 x Tx board
  • 1 x 1-meter LAN cable
  • 2 x 8cm ribbon flex cables for MIPI CSI-2 Transmission
  • 2 x 7.3cm 15-22pin FPC Cable
  • 1 x pack of mounting screws

Notes

  • The package contains small contents, please keep it away from children to avoid accidental ingestion
  • After receiving the package, please confirm whether the contents of the package are consistent with the description
  • No SBC board/Camera Board is included in the package

Note on Supported Raspberry Pi Boards and OS
Platform Bookworm(rpicam) Bullseye(libcamera) Buster(raspistill)
Raspberry Pi 5    
Raspberry Pi 4B / 3B+ / 3A+ / Zero / Zero 2 W
Raspberry Pi CM3 / CM3+ / CM4
(extra carrier board required)


Documentation


Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account